Laboratory Hardware Set: $39.00

Basic Laboratory Tool Set: $12.00

Test Tube Racks
now available in 3 styles...

Wooden Test Tube Rack
Our 12 hole wooden rack is hand carved / finished and imported from India. Overall measurements are 17" long x 3.25" high. Very nice looking test tube rack and what we use in our labs here.
12 Test Tube Rack: $9.00

Poly Test Tube Rack
Our basic 6 hole test tube rack is fabricated from polypropylene. Being so, it is highly resistant to virtually all chemicals and acids. Overall measurements are 8.25" long x 3.25" high.
Made in the USA.
6 Test Tube Rack: $4.00

Combo Test Tube Rack
Fabricated from polystyrene, our Combo Test Tube Rack holds 13 test tubes and 6 Pipettes or glass rods/tubes. Overall measurements are 8.75" long x 3.5" high. Made in the USA.
Combo Test Tube Rack: $6.00

Test tubes are just impossible to get clean without a good 'ole Test Tube Brush. White nylon bristles and a galvanized wire handle. Overall length is 9".
Test Tube Brush: $1.25

Extra heavy construction - fabricated from chrome plated 1/4" steel rod. Can hold Beakers from 50 ml to 1500 ml. Plastic coated tongs.

Beaker Tongs: $4.50

6" long Stainless Steel scoop ideal for removing powdered chemicals from jars. 
Powder Scoop: $2.00

Our lab Spatula features a 6" long flexible Stainless Steel blade and a 4" hardwood handle. Nicely polished. Blade is 1" wide.
Spatula: $4.50

This is both an excellent and affordable kit for vacuum filtration.
A specialized funnel with a flat, perforated bottom (known as a Buchner Funnel) is used with a Vacuum Filtering Flask and Vacuum Pump. Suction from the pump forces the liquid to be filtered through the filter paper. This dramatically speeds up filtration of solutions that can take hours to filter on their own.
Included in the kit is: 
one 500 ml Filtering Flask, one 90 mm porcelain Buchner Funnel, 100 sheets of 90 mm Filter Paper, one specialized Rubber Stopper (to accept the large Buchner Funnel neck), and a lab-quality hand operated Vacuum Pump with gauge. The kit comes packed in a box for easy storage.

Vacuum Filtration Kit: $49.00

Acid or Alkali?
PH Test Paper is one of the most useful tools in a laboratory. This is wide range PH Test Paper (PH 1 - 14), ideal for just about any use from testing the acidity of soil to general chemistry uses.
Simply dip the paper strip in the solution to be tested and in seconds the paper will change color. Hold the strip up to the color chart on the vial and you'll instantly know the PH of the solution. PH paper is preferred by many chemists over expensive electronic PH meters that require frequent calibration and electrode replacement.
Inexpensive & foolproof.
Each vial contains 100 strips.

PH Test Paper, 1 vial: $2.50

High quality, quantitative,
medium-smooth Filter Paper.
Pre-treated with double acid. Washed
with distilled water. Negligible ash
content of 0.01%. Ideal for precise
Quantitative Analysis.
15 cm ( 6" ) diameter circular Filter Paper.
Box of 100 circles.

Filter Paper, 1 box: $12.00

Perfect for any standard Pipette, this 3-valve squeeze bulb makes it easy to transfer precise amounts of liquids.
Simply squeeze the bulb to set up the vacuum - then when desired, press the valve to draw in your liquid. 3 valves allow venting to the Pipette, back of the bulb, or to a side fitting.
Pipette not included.


Pipette Squeeze Bulb: $5.00

Wide range, -10°C to +150°C Thermometer.
Engraved black graduations and easy to read red Spirit filled.
Measures approximately 12" long with integral ring on top for suspension.

Laboratory Thermometer: $8.00

This support stand features a very heavy cast iron base and chrome plated support rod. The heavy base will make sure your expensive glassware doesn't fall over and break - no matter how many clamps and widgets you attach to it.
The thick chrome plating on the rod will not flake off or rust.
The base measures 5" x 8" and the support rod is 20" long.
See below for a variety of Support Stand clamps and attachments...

 Support Stand: $12.00

Bosshead Clamp Holders. High strength Zinc alloy screw Clamp Holders for attaching just about any type of clamp to rods up to 18 mm in diameter. Black powder coated finish.

Clamp Holder: $5.00

Heavy duty Nickel plated Brass 3 finger Clamp.
3 Finger clamps are used to hold larger pieces of glassware and odd-shaped objects.
Rubber covered jaws provide a six point contact for a secure, firm grip on objects up to
100 mm in diameter. Use Clamp Holder (above) for attaching to support stand rods.
Overall length is 13"

3 Finger Clamp: $14.00

A great universal clamp for holding all your glassware, etc.
Strong, interlocking jaws are lined with cork for a firm, secure grip.
Nickel plated brass thumbscrew and anodized aluminum stem. Jaws will open up to about 90 mm.
Use Clamp Holder (above) for attaching to support stand rods.
Overall length is 10".

Extension Clamp: $7.00

Another superb universal clamp for holding all your glassware from Test Tubes to Burets.
Clamp rotates a full 360° and can be locked at any angle. Rubber lined jaws open from 1/2" to 1-3/4". Accepts rods up to 3/4" diameter. Overall length is adjustable from 7.5" to 8".

General Purpose Clamp: $9.00

Cast iron with a powder coated hammertone finish. Nickel plated brass clamping screw.
Use Support Rings for resting flasks and other glassware above an Alcohol Lamp or other heat source. Never heat glassware directly with a flame, always rest the glassware on a Wire Gauze Square (see below). Your choice of 3" or 4" diameter. Overall length is 7".

Support Ring, 4" diameter: $6.00

Tripod burner stand with a cast iron ring finished in hammertone and chrome plated steel legs.
The legs unscrew and are removable.
The ring is 3" diameter, legs are 6" long.

Tripod Stand: $7.00

Although most laboratory glassware is Pyrex, Bomex or similar heat resistant glass, none of them should ever be in direct contact with a flame. The only exception is a Test Tube and even that should be kept moving in & out of the flame. The proper way to heat materials in laboratory glassware (when using an open flame) is to place a Ceramic Center Wire Gauze between the flame and glassware.
Ours is an extra stout wire gauze with a fireproof ceramic center. The sides are turned in so no sharp edges protrude.
Recommended for all glassware.

 4" Wire Gauze w/Ceramic Center: $2.00

The classic Bell and Vacuum experiment.
Used to demonstrate the principle that sound does not travel in a vacuum.
The bell is self contained and battery powered so it requires no external power. Comes complete with battery powered Bell, heavy glass Bell Jar, Vacuum Pump Plate and Vacuum Hose. Assembled unit is 8.5" diameter x 11.5" high. The Bell and circuit board inside are removable so the Jar and Vacuum Plate can be used for a variety of other vacuum experiments.

Bell and Vacuum Apparatus: $54.50

We only recently started stocking these Butane Micro Burners and quite frankly, they are awesome.
Easily portable throughout the entire lab and no need to run gas lines. The Micro Burner is completely self-contained and has its own refillable Butane tank.
Fully adjustable flame control from 0 to 100% simply by rotating the knob as shown above. No matches or igniters required.... the convenient piezoelectric push button on the handle produces a high voltage spark which ignites the burner instantly. Large diameter base offers excellent stability and tip resistance.
Burns about 1.5 hours per fill. Height: 3.35". Produces a flame temperature over 2,500°F.
Excellent for all lab work including bending, shaping & melting standard flint glass tubing. 
Please note that due to shipping regulations, the burner must be shipped empty. You must fill the unit with standard butane lighter fuel (available at any grocery store for about $1.00 to $3.00) before use.

Butane Micro Burner: $39.00 

A versatile Alcohol Lamp/Burner for Lab use where a low temperature flame is desired. Unique hexagonal shape permits the burner to be used standing upright, or tilted to various angles for applying heat in tight spots. Thick glass construction complete with wick & metal cap. Uses Denatured Alcohol for fuel, available at any hardware store, Home Depot, etc. (BTW, for those very observant types, no, the flame above is not an alcohol flame. We put Kerosene in the lamp to make flame bright & yellow so it would show up in the web page image. Give yourself a big pat on the back if you noticed the flame color / brightness was incorrect for an Alcohol lamp.) 

If you've ever tried to drill a hole in a rubber stopper, you know it just doesn't work. The only way to cut a clean hole in a stopper is with a Boring Machine.  Adjustable 'V' stop holds the stopper securely in place during cutting. This is a professional, high quality, heavy cast steel precision boring machine (it weighs about 15 pounds). Machine comes complete with 12 different sized boring bits to quickly slice into any stopper or cork. It will also slice perfect holes in thick leather sheet or similar materials.
Far superior to any other boring or punching device you'll find.
The unit can be bolted to your workbench or used as-is. 

Rubber Stopper Assortment #1
Small Sizes (sizes 00 to 6)
Contains 2 of each size and type (solid, 1 hole, 2hole) from #00 to #6.
(please note that #00 and #0 sizes only come in solid and 1 hole)
Total of 44 stoppers

Rubber Stopper Assortment #1: $15.00

Rubber Stopper Assortment #2
Large Sizes (sizes 7 to 9)
Contains 2 of each size and type (solid, 1 hole, 2hole) from #7 to #9.
Total of 18 stoppers

Rubber Stopper Assortment #2: $15.00